Measuring cylinder, burette and pipette

The above apparatus are used to measure liquid volumes.

Measuring cylinder is also known as graduated cylinder. It measures volumes of liquids to nearest 0.5 cm3. (30.0 cm3, 24.5 cm3).
We use burette to accurately measure volumes of liquids to nearest 0.05 cm3. (29.50 cm3, 38.45 cm3).
Pipette accurately measures fixed volumes of liquids to nearest 0.05 cm3. (20.0 cm3 and 25.0 cm3).

Gas syringe

Gas syringe, as the name suggests, is used to measure volume of gases.

Conical flask and beaker

Conical flask and beaker are commonly used to hold samples, usually liquids. The unique shape of conical flask allows easy swirling of liquid samples without spillage. Rubber bung (with delivery tube) can also be inserted at the mouth of the conical flask, allowing gas to pass through the delivery tube and collected.

Flat bottom flask

Flat bottom flask is also known as volumetric flask. We use it to measure specific liquid sample volumes.

Test tube and boiling tube

Test tube and boiling tube used in laboratory are made of glass (mostly borosilicate glass), not plastics. Hence, they have high heat resistance to heat and corrosive chemicals. To reduce mass loss during transfer of samples, their bottoms are designed to be spherical with vertical sides.

Boiling tube is wider than test tube. It is intended primarily for boiling liquids. We usually heat samples in the boiling tube as the glass is thicker and of higher heat resistance. Heating samples in test tube is also possible but the heat resistance may not be as strong as boiling tube. Test tubes are typically used to hold small amount of samples, usually liquid.

Filter funnel

We use filter funnel to allow easy transfer of substance (usually liquid) into an apparatus with narrower neck.

Bunsen burner

Bunsen burner is used to provide open gas flame for heating. It is connected to the gas source. Rotating the collar at the bottom of the tube controls airflow. If the holes are fully opened, flame will burn hot with blue flame. The hottest part of the blue flame is the tip of the inner flame. If the holes are fully closed, flame will be cooler, and appear orangey yellow, which the safety flame. We avoid heating using the yellow flame as it leaves a black layer (soot) on the bottom of the heated apparatus.

We will place the tripod stand above a Bunsen burner. Wire gauze is placed on the tripod stand to support the apparatus that contains the samples to be heated.

Separating funnel

Got a mixture of oil and water? We can separate the different liquid layers using a separating funnel.

Separating funnel is used to separate immiscible liquids of different densities. Liquid of a lower density will float to the top. Denser liquid will be collected first. Tap is closed before the top part of the denser liquid flows out completely. Sample of the denser liquid is collected in the beaker.

We will then open the tap and allow liquid to flow into another beaker. Then, close the tap when a little of the less dense liquid flows into the beaker. We will have a mixture of the immiscible liquids in this beaker which should be disposed. Pure sample of the less dense liquid is left in the separating funnel and can be tapped off into another clean beaker.

Don’t forget to subscribe to the channel for more Chemistry learning videos. Have fun learning Chemistry 😊

More on
Experimental Chemistry

Measurement and Experimental Design

• Common Gases and their properties

• Common Laboratory Apparatus and their functions

• 40 Chemical Substances All Students Must Know

Purification:

• Setting up and Interpreting Paper Chromatography

• How to separate sand and copper(II) sulfate salt from its mixture

• Filtration to separate insoluble solid from liquid

• How to separate immiscible liquids using Separating Funnel

• Miscibility of liquids

• How to separate miscible liquids using Fractional Distillation

• What is Simple Distillation

Qualitative Analysis

• How to distinguish lead(II) ions from aluminium ions?

• Why calcium ions do not form precipitate with aqueous ammonia

• Identification of Anions

• Identification of Cations using aqueous Ammonia (Flowchart available)

• Identification of Cations using aqueous Sodium Hydroxide (Flowchart available)

• Identifying Anions

• Identifying Cations